拥有高光高色泽,主要用于金属表面、白铁表面、不锈钢表面、玻璃表面、UV表面、强化表面、电镀表面等材料上,具有高色泽、高色彩、高遮盖力、高稳定性、耐酒精及*擦之特点。
印刷:丝印移印均可。
表干及实干时间:表干时间自然挥发5-10分钟;实干时间在24小时以内(加*固化剂)。
稀释及清洗:SV3慢干开油水、UVK1(移印开油水)同时可使用718洗网水清洗。
测试方法(完全干燥后):
1、3m胶纸粘在画有百格的油墨表面,45度角迅速拉起不脱油;
2、纯度99%的工业酒精,一千克砝码用棉布包住在油墨表面,以水平力来回拉200次无脱色;
3、 *:橡皮擦500g力水平来回擦500次。
使用方法:
1、使用前应充分搅拌,用后*封闭;
2、搅拌时加开油水10-15%,稀释到印刷粘度如需自干加*固化剂5%-10%.
3、网板塞网时可用洗网水清洗;
4、不得与其它类型油墨混合使用。
1、适用范围:本产品主要用于各种金属、玻璃、陶瓷、石材、电镀、阳极氧化铝表面、静电喷漆面及烤漆面等制品的丝印及移印;不需加固化剂,不需烘烤,即可获得优异的附着力。
2、产品特性:哑光、附着力佳、耐酒精、耐冲压。
3、稀释剂:用B-03*稀释剂或783开油,用718洗网水清洗网版。
4、固化剂:可选择添加
5、油墨调配方法:开罐先搅拌均匀,取所需量油墨稀释到合适印刷粘度。如需添加固化剂,先加固化剂搅拌后静置10分钟,待油墨与固化剂完全交联后再进行稀释。
6、干燥时间:常温干燥,表干时间5-10分钟,实干时间在24小时以内,48小时后达良好性能,烤箱80℃烘烤30分钟性能更优。
7、添加固化剂后的使用时限:4-6小时,过期请弃用,剩余油墨不可回收。
【性能检测】
1、3M胶带划百格测试:100%无脱落
2、耐冲压测试:1mm厚铝板180°折弯无变化。
3、耐酒精测试:用脱脂棉沾浓度99%工业酒精以500G力水平来回200次无脱色。
【注意事项】
1、先小量试印确认符合要求后再批量生产。
2、做好承印物的表面清除油脂及杂质工作,以促进附着效果。
3、附着力、硬度、耐酸性、耐酒精性、耐化学品性、抗划伤性、*性等性能的检测,需要完全固化后方可检测。
4、未经允许情况下,不得将本系列油墨与其它类型油墨混用及配色。
5、油墨,稀释剂使用及储存时严禁烟火。
6、使用时注意施工场所的通风状况良好,尽量避免皮肤直接接触。
7、本品不慎溅入口、鼻、眼、耳内,应用大量水清洗或直接求助医生。
Metal ink[ ] technical referenceProperties of ink:With high gloss and high color, mainly used for metal surface, the surface of the surface of stainless steel, iron, glass surface, UV surface, enhanced surface, plating and other materials, with a high color, high color, high covering power, high stability, high alcohol and rub characteristics.Printing: screen printing can be.Surface drying and drying time: surface dry time natural volatile 5-10 minutes; work time within 24 hours ( with special curing agent).Dilution and cleaning: SV3 slow dry open water, UVK1 ( printing open water) can be simultaneously used 718 washing network water cleaning.Test method ( completely dry ):In 1, 3M gummed paper in paintings of the surface of the ink, 45 degree angle quickly pulled off the oil;In 2, 99% of the purity of industrial alcohol, one kilogram of weight of cotton pack in the ink surface, with a horizontal force pulling back and forth 200 times without decolorization;3: 500g force levels, wear-resistant eraser brush back and forth 500 times.Method of use:In 1, before use should be fully stirred, use at any time after the closure of;2, add water mixing 10-15%, diluted to printing viscosity for self stem plus special curing agent 5%-10%.3, mesh plug mesh used when washing network water cleaning;4, not with other types of ink mixing.1, the scope of application: This product is mainly used for a variety of metal, glass, ceramic, stone, electroplating, anodic alumina surface, electrostatic spray painting surface and the paint surface and other products, screen printing and printing; without curing agent, without baking, can obtain excellent adhesion.Product characteristics: 2, Matt, adhesive force is good, ethanol tolerance, punching resistance.3: B-03 special thinner, thinner or 783 oil, 718 washing network water cleaning screen.4, curing agent: can choose to add the