点击图片查看原图
a.对小面积之批覆物建议使用涂刷方式（使用油漆*毛刷）。
b.使用涂刷时不需稀释可直接使用或是涂刷粘度需求酌量加稀释剂（以bac或甲苯均可），稀释剂添加量应以≦5﹪为宜以避免降低其遮盖力。
c.夜光漆系属（油性自干性喷/刷漆），内含有极性机溶剂调制而成，对一般水性漆、弹性涂料漆面恐有侵蚀之疑，为慎重起见使用前请于小面积或隐蔽处先行试用。
1.涂刷前应先清洁被覆物表面，如不平整请先将披覆物表面修缮平整且待其完全干燥后，再预先喷涂压克力系列白色（平光）底漆为佳。
2.为使夜光漆蓄光效果更佳建议于涂刷前务必喷涂压克力系列白色（平光）底漆为底层。
3.待喷涂或涂刷之底漆完全干燥后，再进行涂刷夜光漆，涂刷被覆物时请采以同方向方式完成一次厚涂作业，静待15-20分钟待其表面略为干燥之后在以前述相同方式进行第二道作业。
4.涂刷施工时毛刷请勿以上下或左右移动方式来回涂刷，以避免使夜光粉游走产生分散不均匀，导致于严重影响其蓄光能力。
5.每道涂刷间隔时间以15-20分钟为宜，建议至少应涂刷四道为低基准视涂刷后之均匀情况可再追加第五道或更多，随漆膜厚度之增厚其蓄光能力更强（即夜间亮度更佳）。
6.夜光漆（指触干燥时间约20-30分钟），涂刷完成后可视需求再度喷涂或涂刷上透明漆，以使夜光漆表面更加亮丽使用时间更加持久。
夜光漆施工:夜光涂料要经过涂刷形成漆膜以后才能发挥功能。因此要充份
注意事项：发挥夜光涂料的性能，必需做到完整与正确的施工。以下是施工上的注意事项：
(1)了解夜光涂料性能按规定方法施工：若为*施工时：建议喷涂高分子披覆剂一至二层于底层及完成之漆膜上，如此可增强附着性、耐候性与漆面寿命。
(2)做完整的表面处理：表面处理的适当与否，对漆膜之性能与寿命有很大的影响，因此必须要完全除去铁锈、油脂等异物并充份干燥后才能施工刷涂。
(3)夜光涂料应充分搅拌均匀：夜光涂料系颜料、树脂液与耀德兴科技长效长余辉夜光粉之混合物，从制造到使用，可能有一段时间，而难免有颜料、耀德兴科技夜光粉之分离与沉淀，因此在使用前应充分搅拌均匀。
(4)一次之刷涂厚度不宜太厚：一次之刷涂厚度如果太厚时，容易产生泻流，起皱等现象。因此要做适当之控制，做多层叠涂装施工。
免费提供：夜光粉使用方法|发光粉使用技术|荧光粉用法用量|金葱粉使用说明|铜金粉产品介绍|铝银粉生产技术|珠光粉技术支持|反光粉产品说明|雪花粉材料介绍|长效夜光粉怎么用找耀德圣科技。
a small area of ??the approvals recommended brushing way (using dedicated paint brush).
Use brushing without dilution can be used directly or brushing viscosity needs to consider adding diluent (bac or toluene can be), thinner, add the amount of
≦ 5% is appropriate in order to avoid reducing its hiding power.
c Department of luminous paint is (the Oily since dry spray / painting), containing polar solvents modulation by general water-based paint, elastic coating paint fear
Erosion of the suspect, try out as a precautionary measure before use in a small area or shelter.
Brushing before you clean the surface of the coating material, such as uneven Please repair flat coated surface Judai completely dry, and then pre-spray pressure g
Force series white (plain) primer better.
2. Superior proposal for luminous paint STORING effect of brushing before, be sure to spray acrylic series white (plain) primer underlying.
Be spraying or brushing primer is completely dry before brushing luminous paint, brushing the coating material is mining the same direction once thick coating for
Industry, wait 15-20 minutes to wait until the surface is slightly dry after the second operation in the same way as the aforementioned.
4 brushing construction the brush Do more under or move around way back and forth brushing to avoid luminous powder wandering produce non-uniform dispersion, resulting in strict
Weight affect the light-storing capacity.
Every 15-20 minutes is appropriate, it is recommended brushing time interval should be brushing at least four of uniformity in the minimum benchmark, as brushing then an additional
Five or more, with a film thickness of thickening a more light-storing capacity (ie the brightness better at night).
6. Luminous paint (touch dry time of
A more beautiful more durable with time.
The luminous paint construction: luminous paint film formed after brushing to function. Therefore fully
Note: the play of luminous paint performance, it is necessary to do a complete and correct construction. Notes on construction:
(1) to understand the performance of luminous paint construction: the required method to recommend spraying polymer coated agent for professional construction: one to the second floor of the underlying and completion
On the film, so can enhance the adhesion, weatherability and paint life.
(2) to do a complete surface treatment: surface treatment is appropriate or not, have a great impact on the performance and life of the film, and therefore must be completely removed
Rust, grease, and other foreign matter and fully dried before construction brushing.
(3) The luminous paint should be fully Stir: Department of luminous paint pigments, resins, liquid and Yao Dexing long-lasting long afterglow luminous powder mixture from the system
Made to use, there may be a period of time, inevitably pigment, separation and sedimentation of Yao the Dexing Technology luminous powder, stir before use
Uniform.
(4) once the brush thickness should not be too thick: If the thickness is too thick, it is easy to produce diarrhea flow, wrinkling and other phenomenon once the brush. Therefore what is appropriate
Control, multi-layered coating application.
